Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
The Triceratops 3d Printed SE Razor
#11
Wink 
(12-20-2020, 01:02 PM)Wchnu Wrote: We might have to start a 3d printed razor board.
I think It's enough to use the right thread in the right section.
https://www.tost3.com/showthread.php?tid=261
Where there is a great desire there can be no great difficulty - Machiavelli & Me
Greetings from Ischia. Pierpaolo
https://ischiapp.blogspot.com/
The following 1 user Likes ischiapp's post:
  • GAW9576
Like Reply
#12
(12-19-2020, 07:40 PM)Ordinaryshaver Wrote: Jim, I watched the video, looks like it was a great shave.
Question, and I hope fuzzy doesn't see this, but how hard would it be to shim this razor?

I don't think you can shim it because the blade indexes down into a slot.
Jim - The Cackalacky Kid "Finally, shaving is fun again..." 
The Jayaruh Brushes  - The Clan of Catchers
The following 1 user Likes Jayaruh's post:
  • GAW9576
Like Reply
#13
(12-20-2020, 08:08 PM)ischiapp Wrote:
(12-20-2020, 01:02 PM)Wchnu Wrote: We might have to start a 3d printed razor board.
I think It's enough to use the right thread in the right section.
https://www.tost3.com/showthread.php?tid=261

You make a solid point. I will fix it
Happy shaves to ya!
The following 1 user Likes Wchnu's post:
  • GAW9576
Like Reply
#14
I just picked up a 3D printer this weekend. First order of business was to print a razor. You guessed it, The Triceratops. What a great choice that was. This razor ROCKS. Design is spot on and performance to match. 

Great job to the designer of this.


Attached Files Thumbnail(s)
       
Lost, If found do not return and do not feed.
The following 4 users Like twhite's post:
  • Dave in KY, GAW9576, Jayaruh, riverrun
Like Reply
#15
(03-03-2021, 04:05 AM)twhite Wrote: I just picked up a 3D printer this weekend. First order of business was to print a razor. You guessed it, The Triceratops. What a great choice that was. This razor ROCKS. Design is spot on and performance to match. 

Great job to the designer of this.

Looks awesome Tom.
The following 2 users Like GAW9576's post:
  • Dave in KY, twhite
Like Reply
#16
Good job there twhite.
Happy shaves to ya!
The following 3 users Like Wchnu's post:
  • Dave in KY, GAW9576, twhite
Like Reply
#17
(03-03-2021, 04:05 AM)twhite Wrote: I just picked up a 3D printer this weekend. First order of business was to print a razor. You guessed it, The Triceratops. What a great choice that was. This razor ROCKS. Design is spot on and performance to match. 

Great job to the designer of this.

Congrats on the 3D printer, Tom. The Triceratops was a great choice. Such a fine little razor.
Jim - The Cackalacky Kid "Finally, shaving is fun again..." 
The Jayaruh Brushes  - The Clan of Catchers
The following 1 user Likes Jayaruh's post:
  • GAW9576
Like Reply
#18
Great shave. I did notice that after taking the blade out to dry it. When reinstalling it. It was a bit loose. The plastic on the handle that holds the blade compressed some. I just made a .007 thick piece of brass for a shim. Tightened right up.

Just finished printing the ENDGEM I will try that tomorrow.
Lost, If found do not return and do not feed.
The following 2 users Like twhite's post:
  • Dave in KY, GAW9576
Like Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)