![]() |
|
Williams Mug Shave Soap Williams Wednesday shave. - Printable Version +- tost3 (https://www.tost3.com) +-- Forum: General (https://www.tost3.com/forumdisplay.php?fid=36) +--- Forum: Williams Mug Shave Soap Club. (https://www.tost3.com/forumdisplay.php?fid=54) +--- Thread: Williams Mug Shave Soap Williams Wednesday shave. (/showthread.php?tid=60) |
RE: Williams Mug Shave Soap Williams Wednesday shave. - Droo78 - 06-22-2020 (06-21-2020, 12:11 PM)Wchnu Wrote:It's such a lightweight, mild razor, that I tend to unknowingly use more pressure than needed. Williams is slick but not very protective. I also went XTG (sort of ATG) on my lower neck which is almost always a NO for me. Combined with those factors and using the Contour with a new GEM PTFE blade, it resulted in some lower neck irritation, but the shave result was DFS+ overall.(06-18-2020, 01:31 AM)Droo78 Wrote: Williams WednesdayHow did the Contour work for you? RE: Williams Mug Shave Soap Williams Wednesday shave. - Wchnu - 06-23-2020 Awesome!! Yea pressure sucks. I use a witch hazel touch up pass. It helps some with that. RE: Williams Mug Shave Soap Williams Wednesday shave. - Tony'schin - 06-24-2020 24/06/20 Williams Wednesday Cold Water Shave Brush: Vintage Butterscotch Culmak Plus 1952 Soap: Williams Mug Shaving Soap Razor: MicroMatic Clog-Pruf Blade: Personna Injector (4) Post shave: Cold water Rinse, Shower, EO Infused Astringent Balm: Bart's Balm Lime Balm & Lotion Aftershave: Williams Aqua Velva Musk ![]() A Wonderful Vintage Williams Wednesday. I had a pretty good face lather today, although i did reload for the last pass just to make sure. The injector blades work a treat for me in the MM's and i had a BBS finish from 3 passes. The Clog Pruf doing the business in comfort. A nice Post shave routine to finish off. Stay safe and enjoy your day All. RE: Williams Mug Shave Soap Williams Wednesday shave. - Jayaruh - 06-24-2020 ![]() Williams Wednesday's Shave ![]() Cold Water Rinse Williams Mug Soap Jayaruh #2 Two-band badger Bunny V3 Injector Schick Proline CWR Cella ASB The Williams Mug Soap face-lathered well with my Jayaruh #2 Two-band Badger Brush. Two passes and touch ups with the Bunny V3 Injector with a Schick Proline blade gave me a close, comfortable shave. After a cold water rinse I finished off with Cella ASB. I am clean, smooth, and refreshed... RE: Williams Mug Shave Soap Williams Wednesday shave. - Droo78 - 06-24-2020 (06-23-2020, 05:01 PM)Wchnu Wrote: Awesome!! Yea pressure sucks. I use a witch hazel touch up pass. It helps some with that.Witch hazel does work great. It also works wonders on bug bites. Although I don't list it in my SOTD posts, I actually use witch hazel every shave after rinsing off - Dickinson's or Equate (although since the pandemic set in, Walmart has been out of stock of their Equate witch hazel). RE: Williams Mug Shave Soap Williams Wednesday shave. - Droo78 - 06-24-2020 Williams Wednesday's Shave GEM Jr. Parade GEM Stainless PTFE (2) Omega 11126 Boar Williams Mug Shaving Soap LEA 3-in-1 Aftershave Balm RE: Williams Mug Shave Soap Williams Wednesday shave. - mayer57619 - 06-24-2020 Modern Williams shave today RE: Williams Mug Shave Soap Williams Wednesday shave. - GAW9576 - 06-25-2020 (06-24-2020, 11:32 AM)Tony'schin Wrote: 24/06/20 When you use an injector blade in a Micromatic do you have to modify it at all? I was going to try one but it seemed like the center oval shaped bump in the middle of the blade bed would interfere with the blade. RE: Williams Mug Shave Soap Williams Wednesday shave. - Tony'schin - 06-25-2020 Hi GAW9576, I use personna blades and just put the injector up against the stops then carefully close the cap. Make sure you check alignment, then tighten the top down. Check again to make sure all is ok then off you go. I can use them in an open comb and the clog-pruf. Hope this helps, T RE: Williams Mug Shave Soap Williams Wednesday shave. - GAW9576 - 06-25-2020 (06-25-2020, 09:30 AM)Tony\schin Wrote: Hi GAW9576, I use personna blades and just put the injector up against the stops then carefully close the cap. Make sure you check alignment, then tighten the top down. Check again to make sure all is ok then off you go. Awesome. Thank you. I will try an injector blade in a Micromatic very soon. |